325 dimensions are shown for reference purposes only. dimensions are in inches over (millimeters) unless otherwise specified. specifications and availability subject to change. www.tycoelectronics.com technical support: refer to inside back cover. axicom catalog 1308242 issued 3-03 features surface and through hole mounting types. breakdown voltage between contacts and coil: 1,500vrms. surge withstand between contacts and coil: 2,500v (bellcore). high capacity contact: 2a @ 30vdc. 2 form c contact arrangement. board space saving, vertical mount (14.6 x 7.2mm surface area). immersion cleanable, plastic sealed case. single and dual coil latching versions available. basic insulation (coil-to-contact) according to en 60950 / ul 1950. ultrasonic cleaning is not recommended. mechanical data termination: through hole or surface mount printed circuit terminals. mounting position: any. enclosure: immersion cleanable (ip67) plastic case. weight: .084 oz. (2.5g) approximately. coil data @ 23 c voltage: 3-24v. nominal power: 70mw-140mw, dependent on model. see chart below. initial insulation resistance between mutually insulated conductors: 10 9 ohms @ 500vdc. v23079 (p2) series 5 amp switching, high dielectric dpdt polarized fcc part 68 pc board relay operate data @ 23 c must operate voltage: 75% of nominal or less. must release voltage: 10% of nominal or more. operate time (at nominal voltage) : 3 ms, typ.; 5 ms, max. reset time (at nominal voltage) : 3 ms, typ.; 5 ms, max. release time (non-latching w/o diode in parallel) : 2 ms, typ.; 4 ms, max. release time (non-latching with diode in parallel) : 4 ms, typ.; 6 ms, max. bounce time (at contact close) : 1 ms, typ.; 3 ms, max. maximum switching rate (no load) : 50 operations/s. contact data @ 23 c arrangement: 2 form c (dpdt) bifurcated contacts. material: gold overlay on silver nickel. rating: max. switching voltage: 250vac, 220vdc. max. switching current: 5a. max carrying current: 2a. max switching power: 60w, dc; 62.5va, ac. min. permissible load: 100 v. ul/csa rating: 1a @ 30vdc; 300ma @ 110vdc; 500ma @ 120vac; 250ma @ 240vac. expected mechanical life: approx. 100 million ops. expected electrical life: 50 million ops. @ 10ma, 12v, 10 million ops. @ 100ma, 6v. 1 million ops. @ 1a, 30v, 500,000 ops. @ 500ma, 60v. 200,000 ops. @ 2a, 30v. initial contact resistance: 50 milliohms @ 10ma, 20mv. thermoelectric potential: <10 v. file e48393 file lr45064 operating range @ 23 c@ 85 c nominal must operate max. max. coil voltage voltage voltage voltage resistance (vdc) (vdc) (vdc) (vdc) @ 23 c non-latching, 140mw nominal power 3 2.25 6.5 3.4 64.3 6 4.5 3.375 9.8 5.1 145 15 5 3.75 10.9 5.7 178 18 6 4.50 13.0 6.8 257 26 9 6.75 19.6 10.3 578 58 12 9.0 26.1 13.8 1,029 103 24 18.0 52.3 27.7 4,114 411 single coil latching, 70mw nominal power 3 2.25 9.2 4.8 128 13 4.5 3.375 13.8 7.3 289 29 5 3.75 15.3 8.1 357 36 6 4.5 18.5 9.8 514 51 9 6.75 27.7 14.6 1,157 116 12 9.0 37.0 19.6 2,057 206 24 18.0 74.0 39.2 8,228 823 dual coil latching, 140mw nominal power 3 2.25 6.5 ? 64.3 6 4.5 3.375 9.8 ? 145 15 5 3.75 10.9 ? 178 18 6 4.5 13.0 ? 257 26 9 6.75 19.6 ? 578 58 12 9.0 26.1 ? 1,029 103 24 18.0 52.3 ? 4,114 411 high frequency data capacitance: between open contacts: 2pf, max. between coil and contacts: 1.5pf, max. between poles: 1pf, max. rf characteristics: isolation at 100 / 900 mhz: -39.0 db / -20.7 db. insertion loss at 100 / 900 mhz: -0.02 db / -0.27 db. v. s. w. r. at 100 / 900 mhz: 1.04 / 1.40 . initial dielectric strength between open contacts: 1,000vrms for 1 minute. (1,500vrms on request, consult factory for availability). between coil and contacts: 1,500vrms for 1 minute. (single coil relay). between poles: 1,000vrms for 1 minute. surge voltage resistance per bellcore tr-nwt-001089 (2 / 10 s): between open contacts: 2,000v. between coil and contacts: 2,500v (single coil relay). between poles: 2,500v. surge voltage resistance per fcc 68 (10 / 160 s): between open contacts: 1,500v. between coil and contacts: 1,500v (single coil relay). between poles: 1,500v. environmental data temperature range: -40 c to +85 c. maximum allowable coil temperature: 110 c. thermal resistance: < 165k/w. shock, half sinus, 11 ms: functional: 50g. shock, half sinus, 11 ms: destructive: 150g. vibration, 10-1,000 hz.: functional: 35g. needle flame test: application time 20s, burning time <15s. resistance to soldering heat: 260 c for 10s. users should thoroughly review the technical data before selecting a product part number. it is recommended that users also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application.
326 dimensions are shown for reference purposes only. dimensions are in inches over (millimeters) unless otherwise specified. specifications and availability subject to change. axicom catalog 1308242 issued 3-03 www.tycoelectronics.com technical support: refer to inside back cover. our authorized distributors are more likely to stock the following items for immediate delivery. outline dimensions tht .57 max. (14.5) .39 (9.9) max. .022 (.56) max. .12 2 max. (3.1) .28 max. (7.2) smt wiring diagrams (bottom views) dual coil latching*** note: all diagrams shown in de-energized or reset position. *note: for non-latching versions, coil polarity must be observed. **note: for single coil latching versions, polarity shown results in "set" condition. reverse polarity results in "reset" condition. ***note: the contact position illustrated shows the reset condition. if a positve potential is applied to terminal 1 or 7, the relay adopts the set position. .295 max. (7.5) .37 .006 (9.4 0.15) .217 .006 (5.52 0.15) 4 2 .59 max. (15) .41 (10.4) .020 .002 (0.5 0.05) .018 (0.45) .039 max. (1.0) .29 .006 (7.4 0.15) short terminals extended terminals tht pc board layout (bottom view) smt (solder pad) .204 (5.2) .295 (7.5) .35 (8.9) .43 (10.9) .59 (15) .045 (1.15) .035 .004 (0.9 0.1) .10 (2.54) .004 (.10) 15 3 46 8 10 97 12 smt short terminals smt extended terminals .039 max. (1.0) 134 5 6 7 8 9 10 12 .200 (5.08) .10 0 typ. (2.54) .10 0 typ. (2.54) .037 (0.95) v23079a1001b301 v23079a1003b301 v23079a1005b301 v23079a1011b301 v23079a2001b301 v23079a2003b301 v23079a2011b301 v23079d1001b301 v23079d1003b301 single coil latching* and single coil non-latching** ordering information 1 34 5 8 9 10 12 + - 1 34 5 8 9 10 12 orientation mark (on top of relay) + + - - 7 6 orientation mark (on top of relay) set reset v23079d1005b301 v23079d1011b301 v23079d2001b301 note: mounting height varies dependent upon termination type selected in step 2 of ordering information typical part number b v23079 a10 01 b301 1. basic series: v23079 = p2 miniature, printed circuit board relay. 2. termination: non-latching normal ht. non-latching reduced ht. dual coil latching single coil latching through-hole a10 a20 (1) b12 c11 smt extended terminal d10 d20 (1) e12 f11 smt short terminal g10 g20 (1) h12 j11 3. coil voltage: 08 = 3vdc 11 = 4.5vdc 01 = 5vdc 02 = 6vdc 06 = 9vdc 03 = 12vdc 05 = 24vdc (2) 4. contact type: b301 = bifurcated, 2 form c (dpdt), silver nickel. (1) reduced mounting height of 10.0 mm, as opposed to 10.4 mm (smt) or 9.6 mm as opposed to 9.9 (through-hole). non-latching on ly, not available with 24v coil. (2) not available with termination a20, d20 or g20. recommended soldering conditions (according to cecc 00802) infrared soldering: temperature/time profile (lead temperature) vapor phase soldering: temperature/time profile (lead temperature) packaging information tht p2 relays are shipped in tubes of 50. there are 2,000 relays in a carton. smt p2 relays with long terminals are shipped in reels of 400, with 2,000 relays in a carton. smt p2 relays with short terminals are shipped in reels of 500. there are 2,500 relays in a full carton. 20-40 sec forced external 215 c 180 c 130 c solid line: typical time (s) temperature c 100 c 10 sec ca. 40 sec max. 245 c 215 c 180 c 130 c solid line: typical time (s) temperature c v23079d2003b301 v23079d2011b301 u i = minimum voltage at 23 c after pre-energizing with nominal voltage without contact current u ii = maximum continous voltage at 23 the operating voltage limits u i and u ii depend on the temperature according to the formula: u i tamb =k i ?u i 23 c and u ii tamb =k il ?u il 23 c t amb = ambient temperature u i tamb = minimum voltage at ambient temperature, t amb u ii tamb = maximum voltage at ambient temperature, t amb k i , k ii = factors (dependent on temperature), see diagram -40 -20 0 20 40 60 80 100 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 coil limits ambient temperature, t amb [ c] ----- >
|
